Skip to content - KNX Future-proof technology - KNX Future-proof technology
by MDT

RF-AKK1UP.01 KNX RF + radio switching actuator 1x / 230V / 10A

Original price €146,90 - Original price €146,90
Original price
€146,90 - €146,90
Current price €146,90

Type: MDT RF-AKK1UP.01 KNX RF + radio switching actuator 1x / 230V / 10A

EAN: 4251916148515

Bus System: KNX (RF)

Degree of protection: IP20

Mounting: Recessed

This MDT KNX RF + radio switching actuator can switch 2 appliances individually and receive KNX-EIB telegrams. The outputs are switched via a monostable relay and can be individually programmed using ETS. You have a choice between blocking functions, status feedback, central switching functions and complex time functions such as on / off delay and stair lighting functions. Scene features are also available. This switching actuator works in the bidirectional mode of the KNX RF + system and can be perfectly installed in existing installations without a KNX bus cable. The MDT KNX RF + wireless line coupler (RF-LK001.02) is used for connection to the KNX bus. If there is a mains voltage failure, all outputs are switched off and the status is restored when the mains voltage is restored. You need ETS for commissioning and programming.

- New KNX RF + protocol in system mode
- Commissioning with ETS 5
- Normally open and normally closed operation
- Time functions (on / off delay, stair lighting function)
- Feedback function (active / passive) for all channels
- Logical connections
- 8 scenes per channel
- Central functions and object blocking for forced operation
- Adjustable behavior in case of bus voltage failure / recovery
- Installation in a switch box
- Connection via MDT KNX RF + radio coupler (RF-LK001.02)
- For retrofitting without laying bus cables

Number of outputs: 1
Transmission frequency: 868.3 MHz (for operation within the EU)
Outdoor range: 150 m
Output level: 10dBm
Sensitivity:> -105dBm
Compatibility: KNX RF S-Mode (with ETS5 support)

Maximum switching capacity
Resistive load: 10A
Capacitive load: 14uF
Voltage: 230VAC
Maximum inrush current: 80A / 150µs, 40A / 600µs

Maximum load
Bulbs: 1900 W
HV halogen bulbs: 800 W
LV halogen bulbs: 500 W
Uncompensated fluorescent lamps: 500 W
Parallel compensated fluorescent lamps: 90 W
Maximum number of electronic ballasts: 2

Mechanical switching frequency: 1,000,000
Protection: 10A
Available KNX databases: ETS 5
Supply voltage: 230 V AC / 50 Hz
Power consumption 230 V AC: <0,3 W
Ambient temperature: 0 degrees Celsius to +45 degrees Celsius 

The maximum transmission distance is 150 m at an open-air test site. The range of radio signals in buildings is often stated at 30 m. But due to normal absorption radio signals in buildings there is a real distance:
➢ about 30 m with good requirements: Large free space, good mounting position
transmitter and almost no sources of interference in the radio transmission channel, e.g. large conference room.
➢ Reliability of planning:
about 20m with people in the room and transfer through some plasterboard walls or up to 2 stone walls, about 10m in narrow corridors
➢ The vertical passage of the ceilings must in any case be ensured

Reducing the range of material compared to free space:
Wooden wall, sheet metal wall, glass (without metals) 0-10%
Stone wall, pressed board wall (chipboard) 5-35%
Cement with iron reinforcement 10-90%
Metal, Aluminum (Underfloor heating) almost complete barrier

Link to manufacturer information

Odhadovaná doba doručenia: 6 - 10 dní